Emmons LeGrande
Moderator: Dave Mudgett
-
Stan Knowles
- Posts: 22
- Joined: 9 Feb 2005 1:01 am
- Location: Calgary, Alberta, Canada
- State/Province: -
- Country: United States
Emmons LeGrande
Hi All,
I have been playing my Carter Starter for a while now, and have been looking for another steel. A friend I know has this LeGrande D10 that he has decided to sell. Any pros / cons with this guitar? Has A Day set up that I think I might just try for a while. What is the average cost for a change over to an Emmons setup?
Thanx,
Stan
I have been playing my Carter Starter for a while now, and have been looking for another steel. A friend I know has this LeGrande D10 that he has decided to sell. Any pros / cons with this guitar? Has A Day set up that I think I might just try for a while. What is the average cost for a change over to an Emmons setup?
Thanx,
Stan
-
JW Day
- Posts: 323
- Joined: 23 Feb 2005 1:01 am
- Location: Elizabethtown, Kentucky, USA
- State/Province: Kentucky
- Country: United States
-
Willie Crisel
- Posts: 192
- Joined: 28 Feb 2005 1:01 am
- Location: Charlotte, Tennessee, USA
- State/Province: Tennessee
- Country: United States
-
Michael Dene
- Posts: 357
- Joined: 9 Mar 2002 1:01 am
- Location: Gippsland,Victoria, Australia
- State/Province: -
- Country: United States
Stan,
the cost of the change over would be about an hour of careful but fairly straight forward work on your part, being very careful to write down which hole in the bellcrank and which hole on the changer the rods are connected to, and then just swap them over. It's intimidating the first time you do it but it's really very straight forward.
As far as the LeGrande is concerned I don't know that you could do much better!
------------------
Michael
Emmons LeGrande II D10
Peavey Session 500
the cost of the change over would be about an hour of careful but fairly straight forward work on your part, being very careful to write down which hole in the bellcrank and which hole on the changer the rods are connected to, and then just swap them over. It's intimidating the first time you do it but it's really very straight forward.
As far as the LeGrande is concerned I don't know that you could do much better!

------------------
Michael
Emmons LeGrande II D10
Peavey Session 500
-
Mark van Allen
- Posts: 6426
- Joined: 26 Sep 1999 12:01 am
- Location: Watkinsville, Ga. USA
- State/Province: -
- Country: United States
Stan, as Michael says, the Legrandes are very easy to change setup on. You would have to remove/ refit the rods and pulling fingers for the A & C pedals, leaving the B pedal as it is, and also swapping the parts for the E string raise and lower knee levers. Write down the bellcrank (pulling finger) holes and changer holes that each rod is pulling from, and move the bellcranks on the A And C pedal crossbar so they match where the "other" one was. The only other thing is to take note of how much pedal travel is in the adjustment screw on the pedal pull connection at the body for pedal A & C, as you'll want to swap that setting as well. If you go really slowly and carefully, the whole deal shouldn't take more than two hours, and you'll know a lot more about your guitar.
If you buy that one and need it, let me know and I'll send you the Emmons factory rodding setup for the LeGrande II. Great guitars...
------------------
Stop by the Steel Store at: www.markvanallen.com
If you buy that one and need it, let me know and I'll send you the Emmons factory rodding setup for the LeGrande II. Great guitars...
------------------
Stop by the Steel Store at: www.markvanallen.com
-
Fred Nolen
- Posts: 203
- Joined: 1 Jul 2005 12:01 am
- Location: Mohawk, Tennessee, USA
- State/Province: Tennessee
- Country: United States
Stan,
I have a very early Lashley LeGrande D10 8X4. I'm not sure how old it is but the bell cranks are 4 holers. It is a great guitar that I bought from Herby Wallace some years back. All I have ever done to it is change the strings every now and then and polish it. The tone is great. I recently bought a Rains SD10, like JW Day, for the weight reduction. I think you'll like the Le Grande. You don't often hear bad things about Emmons guitars. Good luck.
Ol' Fred
I have a very early Lashley LeGrande D10 8X4. I'm not sure how old it is but the bell cranks are 4 holers. It is a great guitar that I bought from Herby Wallace some years back. All I have ever done to it is change the strings every now and then and polish it. The tone is great. I recently bought a Rains SD10, like JW Day, for the weight reduction. I think you'll like the Le Grande. You don't often hear bad things about Emmons guitars. Good luck.
Ol' Fred
-
Stan Knowles
- Posts: 22
- Joined: 9 Feb 2005 1:01 am
- Location: Calgary, Alberta, Canada
- State/Province: -
- Country: United States
-
John Lacey
- Posts: 2389
- Joined: 6 Jan 1999 1:01 am
- Location: Black Diamond, Alberta, Canada
- State/Province: -
- Country: United States
-
Ricky Littleton
- Posts: 724
- Joined: 7 Mar 1999 1:01 am
- Location: Steely-Eyed Missile Man from Cocoa Beach, Florida USA
- State/Province: Florida
- Country: United States
I've had my Legrande since '93 and would part with her for anything!!!
Have been through pull changes on both necks and it's a snap!
Ricky...
------------------
Emmons LeGrande - 8x4
Session 400 Ltd, Nashville 112,Hilton Volume pedal, Peterson VS-II Tuner
Dan-Echo, E-Bow, Ibanez Distortion, Bo-Bro, Ibanez Auto-Wah, PX4 Pandoras Box
Have been through pull changes on both necks and it's a snap!
Ricky...
------------------
Emmons LeGrande - 8x4
Session 400 Ltd, Nashville 112,Hilton Volume pedal, Peterson VS-II Tuner
Dan-Echo, E-Bow, Ibanez Distortion, Bo-Bro, Ibanez Auto-Wah, PX4 Pandoras Box