Author |
Topic: traded |
Damir Besic
From: Nashville,TN.
|
|
|
|
Damir Besic
From: Nashville,TN.
|
|
|
|
Damir Besic
From: Nashville,TN.
|
|
|
|
Steven Black
From: Gahanna, Ohio, USA
|
Posted 22 Sep 2014 3:21 pm Zum Double 10 question
|
|
Hello Damir, is that Zum still available? and would you take a beautiful Pedalmaster Double 10 zebra wood looking veneer steel guitar for it? I would ned to send you photos of it. Steve Black. |
|
|
|
Damir Besic
From: Nashville,TN.
|
|
|
|
Damir Besic
From: Nashville,TN.
|
|
|
|
Dick Wood
From: Springtown Texas, USA
|
Posted 24 Sep 2014 5:51 am
|
|
What year is it? _________________ Cops aren't paid much so I steel at night. |
|
|
|
Damir Besic
From: Nashville,TN.
|
|
|
|
Erv Niehaus
From: Litchfield, MN, USA
|
Posted 24 Sep 2014 6:49 am
|
|
When did Bruce get away from the "comb" bellcranks? |
|
|
|
Damir Besic
From: Nashville,TN.
|
Posted 24 Sep 2014 6:53 am
|
|
Erv Niehaus wrote: |
When did Bruce get away from the "comb" bellcranks? |
I have no idea Erv, I'm not an expert on ZUM's ... I don't even know what you talking about... maybe some ZUM expert can chime in, and answer the question...
serial number is D1084419 if that helps _________________ https://steelguitarsonline.com/ |
|
|
|
Erv Niehaus
From: Litchfield, MN, USA
|
Posted 24 Sep 2014 6:57 am
|
|
If you look at the bellcranks, they have mustiple slots for the pull rods, like a comb. The ends of the pull rods have a small pin in them that fits into the bellcrank slots. The later bellcranks are more conventional with a kink in the pull rod to fit the lesser notches in the bellcranks. |
|
|
|
Damir Besic
From: Nashville,TN.
|
|
|
|
Erv Niehaus
From: Litchfield, MN, USA
|
Posted 24 Sep 2014 7:05 am
|
|
Those are "comb" bellcranks. |
|
|
|
Damir Besic
From: Nashville,TN.
|
Posted 24 Sep 2014 7:25 am
|
|
Erv Niehaus wrote: |
Those are "comb" bellcranks. |
thanks Erv, man learns something new every day, and I learned about "comb" bell cranks today... _________________ https://steelguitarsonline.com/ |
|
|
|
Erv Niehaus
From: Litchfield, MN, USA
|
Posted 24 Sep 2014 7:32 am
|
|
Glad I could help! |
|
|
|
Howard Montgomery
From: Topeka, KS US
|
Posted 24 Sep 2014 11:28 am
|
|
If D1084419 is the correct serial number, it was built in 1991. Beautiful guitar. |
|
|
|
Damir Besic
From: Nashville,TN.
|
Posted 24 Sep 2014 11:37 am
|
|
Howard Montgomery wrote: |
If D1084419 is the correct serial number, it was built in 1991. Beautiful guitar. |
that should be the number, I guess it would be 1991 then, like I said, man learns something every day..today I learned that my ZUM is not 1999 but 1991 ...if this post stays up for a couple of months, I will become an ZUM expert lol _________________ https://steelguitarsonline.com/ |
|
|
|
Damir Besic
From: Nashville,TN.
|
|
|
|
Paddy Long
From: Christchurch, New Zealand
|
Posted 25 Sep 2014 7:03 pm
|
|
Bruce went to the newer bell cranks around 1997-98 ! _________________ 14'Zumsteel Hybrid D10 9+9
08'Zumsteel Hybrid D10 9+9
94' Franklin Stereo D10 9+8
Telonics, Peterson, Steelers Choice, Benado, Lexicon, Red Dirt Cases. |
|
|
|
Damir Besic
From: Nashville,TN.
|
|
|
|
Donny Hinson
From: Glen Burnie, Md. U.S.A.
|
Posted 5 Oct 2014 1:45 pm
|
|
Erv Niehaus wrote: |
Those are "comb" bellcranks. |
Also known as "slotted pullers". |
|
|
|
Russ Wever
From: Kansas City
|
Posted 6 Oct 2014 1:10 am
|
|
Erv Niehaus wrote: |
Those are "comb" bellcranks. |
Also known as 'center-pull' bell cranks. _________________ www.russface
www.russguru |
|
|
|
Damir Besic
From: Nashville,TN.
|
|
|
|
John Russell
From: Austin, Texas
|
Posted 8 Oct 2014 11:26 am Comb bell cranks
|
|
Although Bruce has gone to the more conventional type bell cranks, the "comb" bell cranks work just fine. They have six slots to fine tune the pull rod's travel so the action can be adjusted however you prefer. The pull rods have a small steel pin that fits in the slot(s) and fits in between the two halves so there's no loss of motion as with some other types of cranks that pull from the side. The only disadvantage is the cranks tighten onto the cross shafts via an allen screw that is parallel to the body between the cross shaft and the body. You need long Allen wrenches with the ball ends to tighten or loosen these. |
|
|
|
Damir Besic
From: Nashville,TN.
|
Posted 8 Oct 2014 1:12 pm
|
|
down to $3550 this is a bargain, there is no other D-10 ZUM out there for 35 hundred bucks.. _________________ https://steelguitarsonline.com/ |
|
|
|