| Author |
Topic: Question about Hilton pedal |
Terry Sneed
From:
Arkansas,
|
Posted 28 May 2018 7:25 pm |
|
How do you tighten a Hilton vp up so it's
not so easy to mash down? Mine goes down
by itself almost. Thanks |
|
|
|
Richard Sinkler
From:
aka: Rusty Strings -- Missoula, Montana
|
Posted 29 May 2018 7:33 am
|
|
Try tightening the screws at the pivot. I think that is what I did.
_________________
Carter D10 8p/8k, Dekley S10 3p/4k C6 setup,Regal RD40 Dobro, NV400, NV112 . Playing for 54 years and still counting. |
|
|
|
Terry Sneed
From:
Arkansas,
|
Posted 29 May 2018 9:45 am Hilton
|
|
Thanks Richard, I've tightened the pivot
screws as tight as they'll go, is there some
other way to tighten the pedal? |
|
|
|
Greg Thompson
From:
Taumarunui, New Zealand
|
Posted 29 May 2018 2:39 pm
|
|
| I think Keith suggests 'O'rings or plastic washers on pivot bushing |
|
|
|
Eric Dahlhoff
From:
Point Arena, California
|
Posted 29 May 2018 2:55 pm
|
|
I "think" there is an adjustable spring inside.
I opened mine once to wire up a tuner output.
It's easy to open - take out the pivot screws. Washers will fall out. It's harder to put it back together... 
_________________
"To live outside the law you must be honest." (Bob Dylan) |
|
|
|
Greg Thompson
From:
Taumarunui, New Zealand
|
Posted 29 May 2018 4:06 pm
|
|
| I need to do mine too Terry, so will be interesting to find out from those that have done it |
|
|
|
Terry Sneed
From:
Arkansas,
|
Posted 29 May 2018 4:52 pm Hilton
|
|
Thanks y'all, I reckon I'll just open it up and
see what's in there. Can proably get some
o rings at Home Depot. 👠|
|
|
|
Jim Bob Sedgwick
From:
Clinton, Missouri USA
|
Posted 30 May 2018 9:36 am
|
|
| Terry this might help. Take the pedal apart. On the right side you will see a Phillips head screw. tighten this just a little and problem is fixed. As stated it's harder to get the pedal back together. O rings will not help. |
|
|
|
Terry Sneed
From:
Arkansas,
|
Posted 30 May 2018 9:56 am Hilton
|
|
| Thanks Jim Bob , I'll try that . |
|
|
|
Bill Burch
From:
California, USA
|
|
|
|
Jim Bob Sedgwick
From:
Clinton, Missouri USA
|
Posted 30 May 2018 6:32 pm
|
|
There you go Terry. This will get you up and running  |
|
|
|
Richard Sinkler
From:
aka: Rusty Strings -- Missoula, Montana
|
Posted 31 May 2018 7:22 am
|
|
Looking at the instructions, I now remember adjusting it with a screwdriver in the heel end of the pedal. No need to take it apart.
_________________
Carter D10 8p/8k, Dekley S10 3p/4k C6 setup,Regal RD40 Dobro, NV400, NV112 . Playing for 54 years and still counting. |
|
|
|
John De Maille
From:
On a Mountain in Upstate Halcottsville, N.Y.
|
Posted 31 May 2018 11:57 am
|
|
Having bought my Hilton pedal used, last year, that manual is a great thing to have.
So far, I've been extremely happy with the pedal and have had no problems with it. It works very well. |
|
|
|
Terry Sneed
From:
Arkansas,
|
Posted 1 Jun 2018 2:11 pm Hilton
|
|
Well shucks, my pedal don't have a screw in
the heel end of the pedal inside or outside .
I reckon it fell out or somethin. May have to
send it back to Keith.  |
|
|
|
