| Author |
Topic: looking for emmons wide floor pedals and crossrods? |
Jack Goodson
From:
new brockton,alabama (deceased)
|
Posted 17 Oct 2020 7:34 am |
|
| i am looking for 3 crossrods and the wide floor pedals for an emmons pp 1973 year model. let me know what you have?....thanks jack....also if anyone has an original pedal board with pedals would also consider that....thanks jack |
|
|
|
Jack Goodson
From:
new brockton,alabama (deceased)
|
Posted 17 Oct 2020 2:18 pm ttt
|
|
| i appreciate any help on this, i really need this to get the ball rolling....thanks jack |
|
|
|
Lynn Stafford
From:
Ridgefield, WA USA
|
Posted 21 Oct 2020 1:59 pm Pedals and Pedal Cross Bars
|
|
Jack,
I can probably provide you with these items. Do the pedals on your guitar have the narrow 2 3/8" spacing? What position, or length do you need? You'll need to provide the length of your existing pedal cross bars. Please measure from the crank plate face to the end of the shaft to be sure you'll have adequate engagement into the support blocks on the rear apron. Hopefully, I'll have ones that are long enough, as they did vary a little through the years.
_________________
Best regards,
Lynn Stafford
STEEL GUITAR WEST
http://www.steelguitarwest.com
Steel Guitar Technician (Restoration, Set-up, Service and Repair work)
Previous Emmons Authorized Dealer & Service Technician (original factory is now closed)
ZumSteel Authorized Service Technician
---------------------------------- |
|
|
|
Jack Goodson
From:
new brockton,alabama (deceased)
|
Posted 21 Oct 2020 2:24 pm Cross rods and pedals
|
|
Here are some photos and measurements.... thanks Jack
 |
|
|
|
Lynn Stafford
From:
Ridgefield, WA USA
|
Posted 21 Oct 2020 4:03 pm Pedals and Pedal Cross Bars
|
|
Jack,
The pedal spacing appears to be the narrow 2-3/8".
I need the length of the round part of the three pedals you need (where the axel goes through). This length varies according to the pedal positions. I'm just trying to see if I have three pedals that will accommodate your needs.
It looks like the length of the pedal cross bars are about 8-15/16" from the end of the shaft to the face of the crank plate, correct?
_________________
Best regards,
Lynn Stafford
STEEL GUITAR WEST
http://www.steelguitarwest.com
Steel Guitar Technician (Restoration, Set-up, Service and Repair work)
Previous Emmons Authorized Dealer & Service Technician (original factory is now closed)
ZumSteel Authorized Service Technician
----------------------------------
Last edited by Lynn Stafford on 21 Oct 2020 5:01 pm; edited 1 time in total |
|
|
|
Jack Goodson
From:
new brockton,alabama (deceased)
|
Posted 21 Oct 2020 4:21 pm Rod is 9 7/16th the pedal is 2 3/8
|
|
| Photo is deceiving. I believe that the pedals are the same width except for the a pedal ....thanks jack |
|
|
|
Jack Goodson
From:
new brockton,alabama (deceased)
|
Posted 22 Oct 2020 12:10 pm Parts?
|
|
| Lynn did you find any pedals or crossroads? Thanks jack |
|
|
|
Jack Goodson
From:
new brockton,alabama (deceased)
|
Posted 22 Oct 2020 2:17 pm Parts?
|
|
| Lynn did you find any pedals or crossroads? Thanks jack |
|
|
|
Lynn Stafford
From:
Ridgefield, WA USA
|
Posted 22 Oct 2020 4:27 pm Re: Parts?
|
|
| Jack Goodson wrote: |
| Lynn did you find any pedals or crossroads? Thanks jack |
Jack,
The cross bars I have are about 1/8" too short (9-5/16") and I don't have any wide pedals for 2-3/8" spacing. The ones I have are for the wide, 2-3/4" spacing, so they would need to be machined shorter.
_________________
Best regards,
Lynn Stafford
STEEL GUITAR WEST
http://www.steelguitarwest.com
Steel Guitar Technician (Restoration, Set-up, Service and Repair work)
Previous Emmons Authorized Dealer & Service Technician (original factory is now closed)
ZumSteel Authorized Service Technician
---------------------------------- |
|
|
|
Jack Goodson
From:
new brockton,alabama (deceased)
|
Posted 23 Oct 2020 11:52 am pedals and cross rods?
|
|
| lynn, would 1/8th shorter be a problem, could i put a stronger spring on the rear apron? also could u send a photo of the pedals u have. the pedal i sent a photo of is the A pedal....thanks jack |
|
|
|
