Author |
Topic: Knobs for LTD 400 |
Dale McPherson
From: Morristown, Tennessee, USA
|
Posted 8 Dec 2019 11:31 am
|
|
Looking for a nice set of the aluminum knobs with the black inserts for a Peavey LTD 400. Also, does anyone have a set of just the black inserts? Thanks, Dale |
|
|
|
Jerry Van Hoose
From: Wears Valley, Tennessee
|
Posted 8 Dec 2019 11:54 am
|
|
Hello Dale, it’s been several years ago but I think that Ken Fox told me where to find a very similar set for my LTD 400, maybe it was Mouser, not sure. I found the black inserts at a local craft store at Governors Crossing in Sevierville. _________________ GFI w/L710, A pair of Peavey Nashville 112’s, Peavey “fex units”, Hilton VP, BJS, Steelers Choice, Furman, Evidence Audio Forte |
|
|
|
Larry Hopkins
From: Lubbock Texas USA
|
Posted 8 Dec 2019 12:25 pm Knobs
|
|
Like Jerry said ,Mouser can probably fix you upðŸ‘
Lh _________________ ,peavey renown 115,Vegas 400, Peavey envoy, peavy bandit 65 head,baby bloomer
2 -Nashville 400, Emmons SD-10 legrande lll ,Emmons Black Rock ,sho-bud pac a seat,,Jackson Madison 63; |
|
|
|
Jerry Overstreet
From: Louisville Ky
|
Posted 9 Dec 2019 7:00 pm
|
|
Dale, I made some dies a few years ago to make some inserts for these knobs. I'm not sure what I did with them, they're prolly here somewhere.
I had 3 types of vinyl or tolex material that I could form these out of.
I sold a few sets for about $25 I believe, for a complete set...with or without the index holes.
Let me know if you're interested and I'll try to dig it all up again.
You probably should measure the centers again, but these are about 19/32 or 15 mm with double stick tape or you can just glue them on.
|
|
|
|
Bob Cox
From: Buckeye State
|
Posted 10 Dec 2019 10:08 am knobs
|
|
I put chickenhead knobs on they look good and can be seen I put chicken head knobs on . They look good and settings are easily seen
|
|
|
|
Dale McPherson
From: Morristown, Tennessee, USA
|
Posted 10 Dec 2019 12:22 pm
|
|
Jerry, If you find those dies.....put me down for a set of inserts. Those look great. I will send a PM later. |
|
|
|
DALE WHITENER
From: TRINITY,NC USA
|
Posted 10 Dec 2019 4:53 pm
|
|
Does anyone have the Mouser part number for those knobs ?
Dale |
|
|
|
Bill A. Moore
From: Silver City, New Mexico, USA
|
Posted 10 Dec 2019 5:59 pm
|
|
I like Jerry's idea!
Just draw some circles on the back of some tolex, and cut them out. |
|
|
|
Ken Fox
From: Nashville GA USA
|
|
|
|
Steven Paris
From: Los Angeles
|
Posted 11 Dec 2019 1:54 am
|
|
$6.51 for ONE knob? YEEESH!!! _________________ Emmons & Peavey |
|
|
|
Ken Fox
From: Nashville GA USA
|
Posted 11 Dec 2019 5:21 am
|
|
Shocking for sure. Used to be around 2.00. Look at what people are selling for on Ebay and Reverb. Prices are very high |
|
|
|
Dale McPherson
From: Morristown, Tennessee, USA
|
Posted 11 Dec 2019 1:38 pm
|
|
Thanks to all who replied. Since my aluminum knobs are in good shape, I was able to find a set of inserts to go in them. Jerry, they are a tad smaller than yours. Thanks again |
|
|
|
Jerry Overstreet
From: Louisville Ky
|
Posted 11 Dec 2019 5:07 pm
|
|
Good deal. Glad you found what you're looking for. If you don't mind me asking, do you know what the inserts diameter is? |
|
|
|
Dale McPherson
From: Morristown, Tennessee, USA
|
Posted 11 Dec 2019 5:16 pm
|
|
Mine are 13.5 mm or 17/32. Basically 1/2". |
|
|
|
Jerry Overstreet
From: Louisville Ky
|
Posted 11 Dec 2019 5:30 pm
|
|
OK, Thank you Dale. Looks like I didn't find the correct die. Still looking. JO. |
|
|
|