| Visit Our Catalog at SteelGuitarShopper.com |

Post new topic Peavey Session 400 Limited amp problem
Reply to topic
Author Topic:  Peavey Session 400 Limited amp problem
James Callan


From:
Philadelphia, Pennsylvania, USA
Post  Posted 9 Sep 2019 1:26 pm    
Reply with quote

About 5 years after I purchased my Session 400 amp (in 1992) it started to get staticky and the sound would just go off some times. At that time whenever this would happen, as a temporary remedy, I would turn the gain (volume) up all the way, attach an electric guitar to the amp input and strum the guitar real hard.The sound would suddenly pop on. I had this problem fixed once by a professional. The technician said the problem was caused by corrosion in the jack hole. He replaced the jack that was creating the problem and it worked fine. About a year later the problem started again. Since then, whenever I use this amp I do the following to alleviate the problem: besides the patch chord I am using for my pedal steel guitar or electric guitar, I insert patch chords in the other inputs on the front of the amp and it works just fine (no more static). Question: I am selling the amp and would like to fix this problem for good. Is there an easy way I can fix this by my self? I don't believe the problem is corrosion in the jacks. I have owned many amps over the years and have never experienced this problem before.
View user's profile Send private message Send e-mail
Bill Miller


From:
Gaspe, Quebec, Canada
Post  Posted 9 Sep 2019 4:38 pm    
Reply with quote

I had the same problem with the one I had. That was a long time ago but if memory serves it had to do with the type of jacks used in those amps ( switching jacks ). There probably isn't any simple solution apart from getting rid of it. I never liked the sound of mine anyways so I wasn't sad to see it go. No fond memories of that particular amp here.
View user's profile Send private message Send e-mail Visit poster's website
Tony Dingus


From:
Kingsport, Tennessee, USA
Post  Posted 9 Sep 2019 6:30 pm    
Reply with quote

I'm having the same problem with my Nashville 112. I dropped it once and later on down the road it started doing the same thing. I hit the strings hard and it works. The preamp out works so I think it's in the power amp. I ran a Boogie pre in the power amp in and had to plug in front of the amp and hit the strings hard to bring it back.

Tony
View user's profile Send private message Send e-mail
Larry Dering


From:
Missouri, USA
Post  Posted 9 Sep 2019 6:41 pm    
Reply with quote

Try using a short jumper from preamp out to power amp in. If it works fine then the jacks are the problem. Seems most of these give trouble after a few years.
View user's profile Send private message Send e-mail
Dennis Detweiler


From:
Solon, Iowa, US
Post  Posted 10 Sep 2019 2:58 pm    
Reply with quote

The patching jacks have contact points toward the back end of the jack and these become corroded sometimes. I've used a piece of folded 400 wet/dry paper and sanded them. Sometimes some contact cleaner will get them working for a while. Molex connectors on the circuit board will be the culprit sometimes. I've also had the power transistor pins on the back of the amp chassis become loose and needed to unplug the power transistors from their sockets and crimp them.
_________________
1976 Birdseye U-12 MSA with Telonics 427 pickup, 1975 Birdseye U-12 MSA with Telonics X-12 pickup, Revelation Preamp, TC Electronic M-350 Processor, Crown XLS 1002 Stereo Rack Head, 15" Eminence EPS-15C, ShoBud Pedal, 1949 Epiphone D-8. And, too much extra gear.
View user's profile Send private message Send e-mail

All times are GMT - 8 Hours
Jump to:  
Please review our Forum Rules and Policies
Our Online Catalog
Strings, CDs, instruction, and steel guitar accessories
www.SteelGuitarShopper.com

The Steel Guitar Forum
148 S. Cloverdale Blvd.
Cloverdale, CA 95425 USA

Click Here to Send a Donation


BIAB Styles
Ray Price Shuffles for Band-in-a-Box
by Jim Baron