Author |
Topic: once again, sorry, volume pedal first or delay? |
Norbert Dengler
From: germany
|
Posted 9 Feb 2019 11:59 am
|
|
this might have been beaten to death, but anyhow, what's your opinion? |
|
|
|
Justin Emmert
From: Greensboro, NC
|
Posted 9 Feb 2019 12:05 pm
|
|
Volume pedal first. Interested to hear other opinions.. |
|
|
|
b0b
From: Cloverdale, CA, USA
|
|
|
|
Drew Pierce
From: Arkansas, USA
|
Posted 9 Feb 2019 8:03 pm
|
|
If there's an Izzy or Match Box, that first, then the VP, then FX, then amp. If the amp has an FX loop, I put FX there and go direct to amp from Izzy/MB/VP. _________________ Drew Pierce
Emmons D10 Fatback, S10 bolt-on, Zum D10, Evans RE500, Hilton volume and delay pedals. |
|
|
|
Ian Rae
From: Redditch, England
|
Posted 10 Feb 2019 1:35 am
|
|
The volume pedal is part of the instrument. You wouldn't put anything between the fiddle and the bow.
The obvious exception is a matching device, which would be like the rosin. _________________ Make sleeping dogs tell the truth!
Homebuilt keyless U12 7x5, Excel keyless U12 8x8, Williams keyless U12 7x8, Telonics rack and 15" cabs |
|
|
|
Richard Sinkler
From: aka: Rusty Strings -- Missoula, Montana
|
Posted 10 Feb 2019 7:05 am
|
|
I put my reverb/ delay in the effects loop of my amp. If it didn't have an effects loop, I would run it after the volume pedal so the volume pedal wouldn't cut off the tails or slap backs when backing the volume pedal down to decrease volume.
A good rule of thumb that I keep seeing is, time altering devices (delay, verb, etc...) should be right before the amp (or in the fx loop). Pedals that react to picking attack (distortion, envelope filter/auto-wah, etc...), before the volume pedal. _________________ Carter D10 8p/8k, Dekley S10 3p/4k C6 setup,Regal RD40 Dobro, NV400, NV112 . Playing for 54 years and still counting. |
|
|
|
Mark van Allen
From: Watkinsville, Ga. USA
|
Posted 13 Feb 2019 3:39 am
|
|
Usually, I’d suggest what Richard says. These are tools, though, so it’s what you want them to do. Some Fuzz, OD, Auto-wah, etc. pedals sound really cool with the ability to change how hard you hit them ( after the VP) Generally I would think most people want to hear the tail on reverb or delay trail off in a natural way, so after VP. But experimentation might give you a whole new sound! _________________ Stop by the Steel Store at: www.markvanallen.com
www.musicfarmstudio.com |
|
|
|
Tiny Olson
From: Mohawk River Valley, Upstate NY
|
Posted 20 Feb 2019 8:31 am
|
|
Nowadays (and for many years) I put the delay between the vol. pedal and the amp. This is when using the Stereo Steel rig or when I use a single, combo amp.
But,,, when I first started using a delay unit in the late 70s, I plugged it directly into the guitar jack using a small, double male plug, then ran to the vol. pedal, then to the amp. It was an Ibanez AD-80 which used two 9v batteries. This was for ease of fast set-up as we did so many package shows where you had 5 minutes to swap out the stage. I got many compliments on my sound though. At that time, very few were using delay. I actually cut at least three of Mr. Watson's albums with that delay plugged into the guitar including, "Sometimes I Get Lucky."
Chris "Tiny" O. |
|
|
|
Dave Mudgett
From: Central Pennsylvania and Gallatin, Tennessee
|
Posted 20 Feb 2019 9:14 am
|
|
For their usual uses as a type of wash, reverb/delay after the volume pedal to hear the natural tail.
However, when doing certain delay effects like hard doubling or the dotted-eighth-note delay trick - see, e.g., this demo by Albert Lee, who was doing this at least 40-50 years ago - https://www.youtube.com/watch?v=Migwfx0wMMc - then if I don't want to hear the trails when I stop, I put a delay in front of the volume pedal so I can cut them off at will. I use these type of delay effects more for guitar, but also occasionally for steel. This is a good use case for two delays, one after volume pedal for a more subtle "delay wash", and one before the pedal for effects like this.
And as mva suggests, there are times that I prefer effects that most people prefer before volume pedal, like OD, distortion, and fuzz, after the volume pedal so I can control how hard I hit them with the volume pedal. For me, everything is context-dependent. |
|
|
|