| Author |
Topic: Session 500 remote switch alteration |
Craig A Davidson
From:
Wisconsin Rapids, Wisconsin USA
|
Posted 1 Feb 2019 11:40 am |
|
| Has anybody rewired the remote switch for a Session 500 so that a 1/4 inch jack could be used? If so do you have a diagram of such? |
|
|
|
Kevin Mincke
From:
Farmington, MN (Twin Cities-South Metro) USA
|
Posted 1 Feb 2019 12:36 pm
|
|
| Craig, If I recall (leg remote not in front of me) that is a midi type (5) pin plug that also controls the phaser effect. I don't believe you'd be able to accomplish the use of all the effects using a 1/4" plug. |
|
|
|
Craig A Davidson
From:
Wisconsin Rapids, Wisconsin USA
|
Posted 1 Feb 2019 2:14 pm
|
|
| Kevin I am willing to accept not having the reverb control if I could get the other two effects. |
|
|
|
Scott Duckworth
From:
Etowah, TN Western Foothills of the Smokies
|
Posted 1 Feb 2019 2:57 pm
|
|
Here's the wiring of how the original 5 pin din plug is wired:
Pin 1 is the string effect (pin 1 and ground)
Pin 2 is the phase shifter (pin 2 and ground)
Pin 3 is the reverb.
They also use the ground pin.
The remote reverb is a 10K Audio pot.
Connect one end to Pin 3, connect the other end of the pot and center (wiper) to ground.
Here's a diagram:
_________________
Amateur Radio Operator NA4IT (Extra)
http://www.qsl.net/na4it
I may, in fact, be nuts. However, I am screwed onto the right bolt... Jesus! |
|
|
|
Richard Sinkler
From:
aka: Rusty Strings -- Missoula, Montana
|
Posted 1 Feb 2019 3:30 pm
|
|
Why wouldn't you use it as is? Are you trying to use it on a differen amp?
_________________
Carter D10 8p/8k, Dekley S10 3p/4k C6 setup,Regal RD40 Dobro, NV400, NV112 . Playing for 54 years and still counting. |
|
|
|
Kevin Mincke
From:
Farmington, MN (Twin Cities-South Metro) USA
|
Posted 1 Feb 2019 3:42 pm
|
|
| Personally, I wouldn’t alter the leg remote for a 500. They are very hard to find and worth$$ to someone without one. Repair yes, alter no. You’d have to most likely drill a hole in back panel to add another 1/4†. |
|
|
|
Scott Duckworth
From:
Etowah, TN Western Foothills of the Smokies
|
Posted 1 Feb 2019 4:24 pm
|
|
| Kevin Mincke wrote: |
| Personally, I wouldn’t alter the leg remote for a 500. They are very hard to find and worth$$ to someone without one. Repair yes, alter no. You’d have to most likely drill a hole in back panel to add another 1/4†. |
You could get another 5 pin mini din plug, and make up a new switch box with cabbaging the old one. I had an old Session 500 that power amp was bad in and made a preamp box with places for a pedal and tuner in it... ran it into a powered PA speaker...
_________________
Amateur Radio Operator NA4IT (Extra)
http://www.qsl.net/na4it
I may, in fact, be nuts. However, I am screwed onto the right bolt... Jesus! |
|
|
|
Craig A Davidson
From:
Wisconsin Rapids, Wisconsin USA
|
Posted 2 Feb 2019 7:06 am
|
|
| Richard Sinkler wrote: |
| Why wouldn't you use it as is? Are you trying to use it on a different amp? |
I wqould love to use it as is but the pin end is so unreliable and I get tired of messing with it. So I figured I could just modify it. |
|
|
|
