Author |
Topic: Carter starter changer fingers |
Jimmie Hudson
From: North Carolina, USA
|
Posted 16 Jan 2019 5:36 pm
|
|
I am in need of 1 complete carter starter changer fingers.
Will buy a complete changer or just 1 complete finger.
Thanks,
Jimmie Hudson call 704-986-6481 8 AM-10 PM EST
Last edited by Jimmie Hudson on 25 Jan 2019 7:10 pm; edited 1 time in total |
|
|
|
Jimmie Hudson
From: North Carolina, USA
|
Posted 18 Jan 2019 7:50 pm ttt
|
|
ttt |
|
|
|
Jimmie Hudson
From: North Carolina, USA
|
Posted 19 Jan 2019 6:04 pm ttt
|
|
ttt.
Also would buy a carter starter parts guitar if you have one. |
|
|
|
Jamie Kitlarchuk
From: Alberta, Canada
|
Posted 19 Jan 2019 6:41 pm
|
|
Try getting in touch with Al Brisco at Steel Guitars Canada. I believe he carries Carter starter parts. |
|
|
|
Jimmie Hudson
From: North Carolina, USA
|
Posted 19 Jan 2019 7:20 pm tried
|
|
Jamie Kitlarchuk wrote: |
Try getting in touch with Al Brisco at Steel Guitars Canada. I believe he carries Carter starter parts. |
I talked to him today. He has no fingers for the starter model guitar. |
|
|
|
Richard Sinkler
From: aka: Rusty Strings -- Missoula, Montana
|
Posted 20 Jan 2019 4:59 am
|
|
That's going to be a tough one. Unless a disgruntled owner took a sledgehammer to theirs. 🔨 _________________ Carter D10 8p/8k, Dekley S10 3p/4k C6 setup,Regal RD40 Dobro, NV400, NV112 . Playing for 54 years and still counting. |
|
|
|
Marty Broussard
From: Broussard, Louisiana, USA
|
Posted 20 Jan 2019 10:56 am
|
|
Jimmie,
FYI, I retrofitted a Fessenden changer to a CS. Moreover, the endlate is easily removed and machined to create a large enough hole to accommodate a different changer.
Good luck on your quest... _________________ RETIRED
"Technique is really the elimination of the unnecessary..it is a constant effort to avoid any personal impediment or obstacle to achieve the smooth flow of energy and intent" Yehudi Menuhin |
|
|
|
Jimmie Hudson
From: North Carolina, USA
|
Posted 20 Jan 2019 6:36 pm fingers
|
|
Marty Broussard wrote: |
Jimmie,
FYI, I retrofitted a Fessenden changer to a CS. Moreover, the endlate is easily removed and machined to create a large enough hole to accommodate a different changer.
Good luck on your quest... |
I have one I need to repair. |
|
|
|
Bent Romnes
From: London,Ontario, Canada
|
|
|
|
Jimmie Hudson
From: North Carolina, USA
|
Posted 22 Jan 2019 5:21 pm finger
|
|
Bent Romnes wrote: |
Those fingers wouldnt be that hard to make if I had one to use for a pattern |
If I can't find one I may send you one to copy. |
|
|
|
Jimmie Hudson
From: North Carolina, USA
|
Posted 25 Jan 2019 7:11 pm ttt
|
|
ttt |
|
|
|
Jimmie Hudson
From: North Carolina, USA
|
Posted 30 Jan 2019 4:44 pm ttt
|
|
ttt |
|
|
|
Jimmie Hudson
From: North Carolina, USA
|
Posted 31 Jan 2019 4:42 pm one more time
|
|
one more time TTT |
|
|
|
Jimmie Hudson
From: North Carolina, USA
|
Posted 4 Feb 2019 7:15 am ttt
|
|
ttt |
|
|
|
Jimmie Hudson
From: North Carolina, USA
|
Posted 6 Feb 2019 11:58 am Close it up
|
|
close |
|
|
|