Author |
Topic: Another ZKing pedal steel build know done pictures added |
Johnie King
From: Tennessee, USA
|
Posted 14 Oct 2018 1:10 pm
|
|
Last edited by Johnie King on 21 Oct 2018 10:38 am; edited 1 time in total |
|
|
|
Johnie King
From: Tennessee, USA
|
Posted 20 Oct 2018 6:40 am
|
|
Pad shelf is detachable very easy just slips into slots.
Last edited by Johnie King on 31 Oct 2018 4:13 pm; edited 3 times in total |
|
|
|
Johnie King
From: Tennessee, USA
|
Posted 21 Oct 2018 10:41 am
|
|
Storage under shelf slots on guitar to accept shelf
Last edited by Johnie King on 26 Oct 2018 8:20 pm; edited 1 time in total |
|
|
|
Johnie King
From: Tennessee, USA
|
Posted 21 Oct 2018 10:43 am
|
|
Last edited by Johnie King on 10 Nov 2018 3:20 pm; edited 1 time in total |
|
|
|
Bobby Nelson
From: North Carolina, USA
|
Posted 26 Oct 2018 2:55 pm
|
|
Nice! |
|
|
|
Richard Sinkler
From: aka: Rusty Strings -- Missoula, Montana
|
Posted 26 Oct 2018 7:18 pm
|
|
Very, very nice. _________________ Carter D10 8p/8k, Dekley S10 3p/4k C6 setup,Regal RD40 Dobro, NV400, NV112 . Playing for 54 years and still counting. |
|
|
|
Fred Treece
From: California, USA
|
Posted 27 Oct 2018 9:03 am
|
|
Johnie, did you make those shelf clips? |
|
|
|
Johnie King
From: Tennessee, USA
|
Posted 27 Oct 2018 9:48 am
|
|
Fred this is a heavy duty set up one can actually put your body weight on shelf it’s not going any where.
Yes Fred the male part part B is 3/16’s inch angle aluminum 2.5 by 2 inches by one inch wide. The part I use too accept the male part is 3/8 thick by two inches wide an 2.75 inches tall.
I’m sure a good hardware store has a commercial fixture for mounting shelves that would simplify the installation.
I miill a 3/16 deep by 1 inch wide slot in this this part to make a slot for part A. Then I attach two part A,s to steel with screws. Screw parts B two shelf An I’m done.
I have a idea for a much easier way to attach shelf stay tuned. |
|
|
|
Fred Treece
From: California, USA
|
Posted 27 Oct 2018 10:22 am
|
|
Johnie King wrote: |
Fred this is a heavy duty set up one can actually put your body weight on shelf it’s not going any where.
Yes Fred the male part part B is 3/16’s inch angle aluminum 2.5 by 2 inches by one inch wide. The part I use too accept the male part is 3/8 thick by two inches wide an 2.75 inches tall.
I’m sure a good hardware store has a commercial fixture for mounting shelves that would simplify the installation.
I miill a 3/16 deep by 1 inch wide slot in this this part to make a slot for part A. Then I attach two part A,s to steel with screws. Screw parts B two shelf An I’m done.
I have a idea for a much easier way to attach shelf stay tuned. |
Okay, thanks. That is the best idea for accessory storage and arm rest I have seen yet, and the brackets look like they make it bomb proof. But I don’t have a mill, so if you have something else up your sleeve that might work just as well, I am definitely staying tuned
PS: by the way, it’s a beautiful guitar too. |
|
|
|
Ron Hogan
From: Nashville, TN, usa
|
Posted 27 Oct 2018 11:07 am
|
|
Johnie,
Very nice. I'll have to come by and enjoy your fine work.
RON |
|
|
|
Johnie King
From: Tennessee, USA
|
Posted 1 Nov 2018 7:04 am
|
|
Thanks Ron when you get a break come on over will open up a new keg of nails. |
|
|
|
Chris Templeton
From: The Green Mountain State
|
|
|
|
Johnie King
From: Tennessee, USA
|
Posted 9 Nov 2018 10:33 am
|
|
Thank you Chris |
|
|
|
Johnie King
From: Tennessee, USA
|
Posted 16 Nov 2018 9:08 am
|
|
I have two of these zking pedal steels your welcome to come check them out at my shop in Nashville Tn.
|
|
|
|
Johnie King
From: Tennessee, USA
|
Posted 16 Nov 2018 9:10 am
|
|
|
|
|
|
Johnie King
From: Tennessee, USA
|
Posted 16 Nov 2018 9:12 am
|
|
|
|
|
|
Johnie King
From: Tennessee, USA
|
Posted 16 Nov 2018 9:19 am
|
|
|
|
|
|