| Author |
Topic: Eminence double T-12 |
Bill R. Baker
From:
Clinton, MS USA
|
Posted 3 Apr 2018 8:13 am |
|
About the Eminence Double T-12 designed by Travis Toy.
Has anyone replaced the speaker in the Nashville 112
with this speaker? If so, then what about a report.
Would certainly be lighter but what about the tone.
thanks,
Bill |
|
|
|
John Swain
From:
Winchester, Va
|
Posted 3 Apr 2018 9:02 am
|
|
| I have one in my Nashville 112, I like the sound and there was no loss in volume! |
|
|
|
Tony Glassman
From:
The Great Northwest
|
Posted 3 Apr 2018 9:17 am
|
|
| Large improvement over the Peavey OEM Blue Marvel speaker tone-wise...and a bit lighter |
|
|
|
Tony Glassman
From:
The Great Northwest
|
Posted 3 Apr 2018 9:18 am
|
|
(oops, double tap)
Last edited by Tony Glassman on 4 Apr 2018 5:59 pm; edited 2 times in total |
|
|
|
Tucker Jackson
From:
Portland, Oregon, USA
|
Posted 3 Apr 2018 12:05 pm Re: Eminence double T-12
|
|
| Bill R. Baker wrote: |
| Would certainly be lighter but what about the tone. |
Tone is in the ear of the beholder, but...nah, nevermind. My buddy put one in has 112 and it's just better. A very good match for that amp.
More accurately, I bet a blind listening poll would have 90% thinking it was a sweeter, better-balanced sounding speaker than the stock one. |
|
|
|
Travis Toy
From:
Nashville, TN, USA
|
Posted 3 Apr 2018 10:04 pm
|
|
The jury has spoken. 
-t |
|
|
|
Michael Dulin
From:
Indiana, USA
|
Posted 4 Apr 2018 10:52 am eminence tt speaker
|
|
| My question is I've only seen this speaker listed as 8ohms...doesn't a nv112 take a 4ohm speaker? Mike Brown told me I would be cutting power putting an 8ohm in place of a 4ohm in my nv112. Does it come in a 4ohm model and I've overlooked it?MD |
|
|
|
John Swain
From:
Winchester, Va
|
Posted 4 Apr 2018 11:25 am
|
|
| You overlooked my post that said great tone and "no loss of volume"! |
|
|
|
Travis Toy
From:
Nashville, TN, USA
|
Posted 4 Apr 2018 11:32 am Re: eminence tt speaker
|
|
| Michael Dulin wrote: |
| My question is I've only seen this speaker listed as 8ohms...doesn't a nv112 take a 4ohm speaker? Mike Brown told me I would be cutting power putting an 8ohm in place of a 4ohm in my nv112. Does it come in a 4ohm model and I've overlooked it?MD |
Hey Michael. It is an 8 ohm speaker. As you can see from others comments, they are having no issues whatsoever. The fear of putting an 8 ohm speaker in a 4 ohm amp is VERY overstated by lots of folks. On paper it might show a loss of power, but in reality, my speaker is a considerably more efficient design than a traditional magnet speaker, so you’ll suffer no loss in power/volume. I’ve not gotten a single negative message from anyone who has my speaker in a NV112. It’s been overwhelmingly positive.
-t
Sensitivities:
Stock 12" Blue Marvel speaker (4Ω) = 96.5 db
Eminence Double-T 12 (8Ω)= 100.2 db
Last edited by Travis Toy on 4 Apr 2018 3:18 pm; edited 2 times in total |
|
|
|
Bill A. Moore
From:
Silver City, New Mexico, USA
|
Posted 4 Apr 2018 3:06 pm
|
|
Travis, most solid state amplifiers specify a minimum load. (many say 4, or even 2 ohms). (You won't blow one up running it with no load!) The Nashville 112 has no aux speaker out, so I would assume they want no less than 4 ohm minimum.
(Leo's tube amps always had an aux speaker jack, as well as safeguards against no load, (high impedance), so he wasn't worried about dropping a DR to 4 ohms, or a Twin to 2!)
The comments about speaker efficiency, (no loss of power), should help folks decide whether to pull the trigger on using a TT speaker in their Nashville 112! |
|
|
|
Travis Toy
From:
Nashville, TN, USA
|
Posted 4 Apr 2018 3:14 pm
|
|
Thanks Bill. ðŸ‘ðŸ»
-t |
|
|
|
Jack Hanson
From:
San Luis Valley, USA
|
Posted 4 Apr 2018 4:23 pm
|
|
| Fully realizing this is an extreme long shot, has anyone tried the TT-12 in a Polytone Mini-Brute II? |
|
|
|
Travis Toy
From:
Nashville, TN, USA
|
Posted 4 Apr 2018 5:48 pm
|
|
| Jack Hanson wrote: |
| Fully realizing this is an extreme long shot, has anyone tried the TT-12 in a Polytone Mini-Brute II? |
I had to look that one up. I have not received any messages from anyone using a TT with that particular amp. That being said, I’ve gotten messages from people all over the globe that have put them in a lot of amps that I’d never heard of. All I can say is this...my speaker is voiced VERY friendly for a modern steel tone. Any amp, especially an amp with a traditionally guitar voiced speaker, is gonna get the benefit of becoming considerably more steel friendly from an EQ perspective. Good luck!
-t |
|
|
|
Jack Hanson
From:
San Luis Valley, USA
|
Posted 5 Apr 2018 7:26 am
|
|
| Thanks, Travis. |
|
|
|
Bill R. Baker
From:
Clinton, MS USA
|
Posted 14 Apr 2018 12:33 pm Thanks
|
|
Thanks to all of you who responded to make this an
interesting and informative post. Great to have
Travis Toy (the man) participate with us. I have
purchased the speaker designed by Travis and it will
ride in my Nashville 112. |
|
|
|
Travis Toy
From:
Nashville, TN, USA
|
Posted 14 Apr 2018 12:35 pm
|
|
Hope you love it Bill. ðŸ‘ðŸ»
-t |
|
|
|
Olli Haavisto
From:
Jarvenpaa,Finland
|
Posted 16 Apr 2018 3:52 am
|
|
What would be the nearest 10†equivalent?
_________________
Olli Haavisto
Finland |
|
|
|
