| Author |
Topic: Photos of Bakelite Neck Repair |
Howard Clark
From:
Brookston, Indiana, USA
|
Posted 1 Jun 2005 10:17 pm |
|
I repaired broken neck the early forties Bakelite Rickenbacher using the Wayne Tanner method suggested to me by Roy Montee. I ordered the Brownell's AcraGlas at a local gun shop and while waiting for it to arrive, I built a clamping gizmo out of 3/4 inch plywood.
The neck pieces fit together perfectly, but when I laid them on the plywood there was a slight gap at the fretboard side, careful examination showed that the neck was slightly bowed. If I didn't know better, I would say that it was neck relief, the slight bowing in a regular guitar neck to compensate for the fact that the greatest amplitude of vibration of a string is at it's center. I suppose the bowing is caused by "creep," deformation caused by 60 years of string tension.
I discovered that if I held the peg head and pushed on the tail end of the neck, the pieces would line up perfectly. I built the gizmo with a loose piece at the tail end and two half-inch threaded rods with wing nuts to apply pressure.
This worked fine except that the neck wasn't perfectly straight. I added two strips of wood on either side of the neck. the neck is a perfect taper from tail end of the fretboard to the nut, so pressure from the wing nuts would actually force it into alighnment. I also added to more strips of wood to keep the threaded rod in alignment. I made a groove underneath the joint and lined it with aluminum tape, so that any drips wouldn't glue the neck to the gizmo.
This worked fine so I mixed up the epoxy, which is mixed 4 to 1 epoxy to hardener. I have two matching sets of stainless steel measuring spoons, so I used one 1/4-teaspoon to scoop out 4 spoonfuls of epoxy resin and the other to measure out one 1/4-teaspoon of hardener. I poured them into a stainless steel measuring cup and stirred for 2 minutes. I then put in 2 drops of black colorant and contued stirring for 2 more minutes. I brushed it on both pieces with a throwaway brush, stuck them together and put the neck into the gizmo, and snugged up the wing nuts. I then turned the wing nuts until it was solid and hard to turn, but I didn't overdo it.
The instructions say that the epoxy reaches full strength after 2-1/2 days, so I left it in for 3 days.
I'll be able to sand down the excess to match the other frets. There is plenty of resin left to fill the low spots where chips popped out.
I strung it up this evening, it sounds wonderful!
Howie Clark[This message was edited by Howard Clark on 01 June 2005 at 11:57 PM.] |
|
|
|
Joel Newman
From:
Smithsburg, Maryland, USA
|
Posted 2 Jun 2005 6:06 am
|
|
| Wow!! Bravo Howard, well done. Perish the thought of anyone else needing that kind 'o TLC for thier bakelite but don't ever throw your 'gizmo' away. . . . |
|
|
|
Terry Farmer
From:
Albuquerque, New Mexico, USA
|
Posted 2 Jun 2005 6:17 am
|
|
| My hat is off to you, sir! |
|
|
|
Denny Turner
From:
Oahu, Hawaii USA
|
Posted 2 Jun 2005 6:24 am
|
|
What excellently planned and executed work, Howard. BRAVO indeed. And THANK YOU for sharing it with us.
Aloha,
DT~
|
|
|
|
Bob Stone
From:
Gainesville, FL, USA
|
Posted 2 Jun 2005 6:44 am
|
|
Howard,
Thanks a million. Your photo illustrations are wonderful. I hope I never have to use this information, but if i do this sounds like the method.
Hats off to Wayne Tanner too.
Bob |
|
|
|
Gerald Ross
From:
Ann Arbor, Michigan, USA
|
Posted 2 Jun 2005 6:52 am
|
|
Howie,
Incredible!! Beautiful work. Well thought out, not rushed and thorough.
You, Wayne Tanner, Bill Creller and Rick Aiello have done a great deal and added to the knowledge base that keeps these old instruments alive and well. Thank you.
See you at the Winchester Aloha convention next month?
------------------
Gerald Ross
'Northwest Ann Arbor, Michigan's King Of The Hawaiian Steel Guitar'
Gerald's Fingerstyle Guitar Website
Board of Directors Hawaiian Steel Guitar Association
[This message was edited by Gerald Ross on 02 June 2005 at 07:53 AM.] |
|
|
|
Michael Aspinwall
From:
Arizona, USA
|
Posted 2 Jun 2005 2:47 pm
|
|
| Your photos & graphics ROCK!! Do you do this for a living?? |
|
|
|
Rick Aiello
From:
Berryville, VA USA
|
Posted 2 Jun 2005 2:51 pm
|
|
What a marvelous job !!!!
------------------
Aiello's House of Gauss
My wife and I don't think alike. She donates money to the homeless and I donate money to the topless! ... R. Dangerfield
|
|
|
|
Jon Light
From:
Saugerties, NY
|
Posted 2 Jun 2005 2:53 pm
|
|
| Great job, superb presentation. |
|
|
|
Danny James
From:
Summerfield Florida USA
|
Posted 2 Jun 2005 3:15 pm
|
|
| That's the kind of work anyone should be proud of. A++ |
|
|
|
Bill Creller
From:
Saginaw, Michigan, USA (deceased)
|
Posted 2 Jun 2005 6:06 pm
|
|
That was a fine job, and well thought out.Like everyone else said,I hope to never have to do it again. Great work!!
BILL |
|
|
|
Howard Clark
From:
Brookston, Indiana, USA
|
Posted 3 Jun 2005 5:55 am
|
|
Thanks for the compliments, but it would be in a UPS scrap sale without the Steel Guitar Forum. Thanks to everyone for your help.
Howie |
|
|
|
HowardR
From:
N.Y.C.-Fire Island-Asheville
|
Posted 3 Jun 2005 9:22 am
|
|
Very excellent as everyone else has stated.
Please don't let my ex get a hold of your device. My voice is high enough!  |
|
|
|
