The Steel Guitar Forum Store 

Post new topic String stuck in the string slot
Reply to topic
Author Topic:  String stuck in the string slot
Greg Koenig

 

From:
Nevada, USA
Post  Posted 16 Aug 2017 7:51 pm    
Reply with quote

I was changing the C6 strings on a gfi ultra and the 9th string is stuck in the string slot. Any advise?
View user's profile Send private message Send e-mail

Lane Gray


From:
Topeka, KS
Post  Posted 16 Aug 2017 11:29 pm    
Reply with quote

Put a knife or slotted screwdriver between string and finger, push downward
_________________
2 pedal steels, a lapStrat, and an 8-string Dobro (and 3 ukes)
More amps than guitars, and not many effects
View user's profile Send private message Send e-mail Yahoo Messenger

David Nugent

 

From:
Gum Spring, Va.
Post  Posted 17 Aug 2017 12:36 pm    
Reply with quote

You might also try a small allen wrench, insert the shorter angled end into the ball and push.
View user's profile Send private message

Larry Jamieson


From:
Walton, NY USA
Post  Posted 17 Aug 2017 5:02 pm    
Reply with quote

Hi Greg,

If you have an awl with a point on it, get the point on the ball end and tap gently with a hammer. Let us know how you make out.
View user's profile Send private message Send e-mail Visit poster's website

Greg Koenig

 

From:
Nevada, USA
Post  Posted 17 Aug 2017 8:32 pm    
Reply with quote

This one has really got me. The ball end isn't stuck I believe it is actually the string is stuck and it has been this way for quite a while. I will try to upload a picture but it is hard to see in there.
View user's profile Send private message Send e-mail

Lane Gray


From:
Topeka, KS
Post  Posted 17 Aug 2017 10:25 pm    
Reply with quote

9 and 10 can get wedged if the lock twist lodges the wrong way in the slot.
In fact, I had already assumed that, and not that the ball lodged in the slot.
The awl or screwdriver should do the trick.
_________________
2 pedal steels, a lapStrat, and an 8-string Dobro (and 3 ukes)
More amps than guitars, and not many effects
View user's profile Send private message Send e-mail Yahoo Messenger

Richard Sinkler


From:
aka: Rusty Strings -- Missoula, Montana
Post  Posted 18 Aug 2017 8:00 am    
Reply with quote

On both my Carter and the Super-Pro I once had, I had to enlarge the slot in the finger. I took a small jewelers srewdriver and pryed up the "wings" of the slots until the ball and twist fit. You really have to have a light touch, as well as confidence, and do a tiny bit at a time. Prying too hard can break the slot open. BE CAREFUL!!!!!!!! Don't do it if you are not confident. Maybe try some smaller strings if they will work. I would try that first. I could never understand why builders went from pins to those stupid slots.
_________________
Carter D10 8p/8k, Dekley S10 3p/4k C6 setup,Regal RD40 Dobro, NV400, NV112 . Playing for 54 years and still counting.
View user's profile Send private message Send e-mail

Brint Hannay

 

From:
Maryland, USA
Post  Posted 18 Aug 2017 11:00 am    
Reply with quote

The advice for getting the string out seems sound, but as for avoiding a repeat of the problem:

My GFI is an SD-10, so no big strings, but I had only a Super Pro for 20+ years, and never altered the string slots. I just figured out a method of installing strings 9 & 10 of the C6 that works fine. Just pre-bend the string with needle-nose pliers so it looks like in my (sloppy) drawing. Then you can hook the ball end under the notch, and the core wire fits into the slot. When tightened the string snugs up against the finger but not inside the slot, so it doesn't get stuck.
View user's profile Send private message Send e-mail

Richard Sinkler


From:
aka: Rusty Strings -- Missoula, Montana
Post  Posted 18 Aug 2017 11:09 am    
Reply with quote

Great advice Brint.
_________________
Carter D10 8p/8k, Dekley S10 3p/4k C6 setup,Regal RD40 Dobro, NV400, NV112 . Playing for 54 years and still counting.
View user's profile Send private message Send e-mail

Tony Glassman


From:
The Great Northwest
Post  Posted 18 Aug 2017 11:51 am    
Reply with quote

Loosen the string until it's slack (or better yet cut it). Put a drop of tri-flow on the claw. Then put an awl thru the Ball end and a pliers on the cut end and work the remnant out.
View user's profile Send private message

Bobby D. Jones

 

From:
West Virginia, USA
Post  Posted 18 Aug 2017 6:45 pm     String stuck in String Slot.
Reply with quote

Been there and done that on the first string change. I have a GFI S 12 Strings 10,11, and 12 can be tricky.
If the awl will not loosen and remove the string as a last thing, Cut the string about 2 inches long, Then get hold of the winding wire end and pull on it slowly it will start sliding up and around the the core wire, Go slow this may relieve the wedging in the slot till it can be removed.

I use a set of rather smooth faced pliers and sort of flatten the string up about 3/4 inch from the ball till it will slide easily into the finger slot.
No problem sliding in or out of the slot once has been done. Good Luck on this project and Happy Steelin.
View user's profile Send private message Send e-mail

Jerry Roller


From:
Van Buren, Arkansas USA
Post  Posted 19 Aug 2017 11:33 am    
Reply with quote

Could you perhaps bend a string half way in the middle and slide both ends down behind the hung string and pull it out from the bottom of the guitar with plier or vice grips.
Jerry
_________________
http://www.littleoprey.org/
View user's profile Send private message Visit poster's website

Greg Koenig

 

From:
Nevada, USA
Post  Posted 19 Aug 2017 12:03 pm    
Reply with quote

Thanks for all the help will let you know how it turns out after I can borrow the right tools. Greg
View user's profile Send private message Send e-mail

Lee Baucum


From:
McAllen, Texas (Extreme South) The Final Frontier
Post  Posted 19 Aug 2017 3:16 pm    
Reply with quote

If you don't have a small enough awl or screwdriver, perhaps an ice pick may work.
View user's profile Send private message Send e-mail

ajm

 

From:
Los Angeles
Post  Posted 20 Aug 2017 6:20 am    
Reply with quote

Try calling GFI and see what they say.

In addition to being able to help, I'm sure that they would want to know about an issue with their products. That is, if they don't already know after being in business for many years.
View user's profile Send private message

Greg Koenig

 

From:
Nevada, USA
Post  Posted 21 Aug 2017 11:26 am    
Reply with quote

Success,

Thanks for the advise. I used a awl and a few love taps and it came right out!

Thank you all!
Greg
View user's profile Send private message Send e-mail

Lee Baucum


From:
McAllen, Texas (Extreme South) The Final Frontier
Post  Posted 21 Aug 2017 7:33 pm    
Reply with quote

Quote:
Thank you all!


Are you sure you didn't mean...

Quote:
Thank you awl!


Laughing
View user's profile Send private message Send e-mail

Larry Jamieson


From:
Walton, NY USA
Post  Posted 22 Aug 2017 5:30 am    
Reply with quote

Funny, Lee.
View user's profile Send private message Send e-mail Visit poster's website


All times are GMT - 8 Hours
Jump to:  

Our Online Catalog
Strings, CDs, instruction,
steel guitars & accessories

www.SteelGuitarShopper.com

Please review our Forum Rules and Policies

Steel Guitar Forum LLC
PO Box 237
Mount Horeb, WI 53572 USA


Click Here to Send a Donation

Email admin@steelguitarforum.com for technical support.


BIAB Styles
Ray Price Shuffles for
Band-in-a-Box

by Jim Baron
HTTP